Skip directly to search Skip directly to A to Z list Skip directly to site content

Polychlorinated Biphenyls (PCBs) Toxicity
What Are Polychlorinated Biphenyls (PCBs)?

Course: WB 2460
CE Original Date: May 14, 2014
CE Expiration Date: May 14, 2016
Download Printer-Friendly version [PDF - 612 KB]

Previous Section Next Section

Learning Objective

Upon completion of this section, you will be able to

  • Describe key characteristics of PCBs.

Definition

PCBs are chemicals formed by attaching one or more chlorine atoms (at the Xs in Figure 1 below) to a pair of connected benzene rings.

PCBs are chemicals formed by attaching one or more chlorine atoms to a pair of connected benzene rings.
Figure 1: Polychlorinated Biphenyls (PCBs)

Depending on the number and position of chlorine atoms attached to the biphenyl ring structure, 209 different PCB congeners can be formed. PCB congeners can be divided into the coplanar, the mono-ortho-substituted PCBs, and other non-dioxin-like PCBs. The significance of this designation is that coplanar and some of the mono-ortho-substituted PCBs have dioxin-like toxicologic effects.

Chemical Properties: Dioxin-like vs. Non-dioxin-like

The chlorination pattern of the PCBs determines the toxicity of the substance. A number of PCB congeners show dioxin-like toxicity. These PCBs have no more than one chlorine atom at the ortho-position (polychlorinated non-ortho and mono-ortho biphenyls). The phenyl rings of these molecules can rotate and adopt a coplanar structure, which leads to the same toxicity as the polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs). The toxic effects of these dioxin-like PCBs are discussed in detail in later sections of this document.

A number of PCB congeners, however, have two or more of the ortho-positions in the biphenyl molecules occupied by chlorine molecules. For these, the two phenyl rings are not in the same plane, and these PCBs express non-dioxin-like toxicity.

Commercial PCB products are mixtures of different PCB congeners and contain small amounts of PCDFs or PCDDs. Contamination is a concern because the toxicity of these contaminants is generally much greater than that of PCBs [ATSDR 2000].

Uses

Because of their insulating and nonflammable properties, PCBs were marketed for nearly 50 years between 1929 and 1977. They were used in making

  • Diffusion pump oils,
  • Extenders for pesticides,
  • Heat exchange and dielectric fluids in transformers and capacitors,
  • Hydraulic and lubricating fluids, and
  • As ingredients in caulking compounds, paints, adhesives, flame retardants, and plasticizers.

In 1977, the United States banned production of PCBs because of their potential carcinogenicity.

Trade Names

The following trade names are used for commercial PCB mixtures:

  • Aroclor
  • Asbestol
  • Askarel
  • Clorphen
  • Diaclor
  • Dykanol
  • EEC-18
  • Eucarel
  • Nepolin
  • Pyranol

Key Points

  • PCBs are manufactured chemicals produced for nearly 50 years in the United States before they were banned in 1977.
  • PCBs were banned because of their potential carcinogenicity.
   

Progress Check

1. Select the best answer from the following choices:

A. Commercial PCB products are mixtures of different PCB congeners.
B. Commercial PCB products commonly are contaminated with small amounts of polychlorinated dibenzofurans (furans) or polychlorinated dibenzodioxins (dioxins).
C. PCB manufacturing was banned in the United States in 1977.
D. All of the above.

Answer:

To review relevant content, see "Chemical Properties and Uses" in this section.

Previous Section Next Section
 
USA.gov: The U.S. Government's Official Web PortalDepartment of Health and Human Services
Agency for Toxic Substances and Disease Registry, 4770 Buford Hwy NE, Atlanta, GA 30341
Contact CDC: 800-232-4636 / TTY: 888-232-6348

A-Z Index

  1. A
  2. B
  3. C
  4. D
  5. E
  6. F
  7. G
  8. H
  9. I
  10. J
  11. K
  12. L
  13. M
  14. N
  15. O
  16. P
  17. Q
  18. R
  19. S
  20. T
  21. U
  22. V
  23. W
  24. X
  25. Y
  26. Z
  27. #